Solar iPod Charger
Solar IPod Charger
Find out how to make a solar powered charger for your iPod
solar | generalMaking a
solar charger for an
iPod is no more difficult than making our
Solar battery charger. Built in iPod batteries are 3.7 Volts with the capacity (measured in mAh) dependent on the type of iPod - e.g. 1,200mAh for a 2nd Gen, 850mAh for a 3rd Gen, 500mAh for the Mini iPod, and 400mAh for the Nano.
In our instructions for making a
solar battery charger for AA and AAA batteries we made a
current limiting circuit. Because the iPod range has batteries of a wide selection of capacities, our
solar iPod charger is instead
voltage limited. Since iPods can be charged via a USB port with a fixed 5 Volts DC, this is the voltage we will use.
Please scroll down to the bottom of this article for details on commercially available Solar iPod Chargers if you are not interested in finding out how to make your own.
The Solar Panel
To make our
iPod solar charger we used a
250mA 6 Volt Solar Panel (available in the
REUK Shop). Even in the brightest sunshine the voltage is not excessively above that of the iPod battery, and the current is plenty enough to charge the battery in a few hours in bright conditions (even in the UK!).
A
blocking diode should be used (in the positive solar panel lead) to prevent the iPod battery from slowly draining at night if it is still connected to the panel. Unforunately this results in up to 0.7 Volts being lost as heat in the diode, so it can be left out if you prefer to have a faster charger which will charge the battery in lower light conditions.
Note that many solar panels are supplied with a factory fitted blocking diode.
Voltage Regulator
In order to regulate the voltage from our
6 Volt solar panel we used an
LM317T chip (available from the
REUK Shop) in the following super simple circuit:
...where
R1 is a 270 Ohm
resistor, and
R2 is theresistor used to set the
output voltage according to the following equation:
|
R2 = R1 * ( (VOUT/1.25) -1 )
|
Since our desired charging voltage is
5 Volts, we see that ideally
R2 would be 270 * ((5/1.25) -1) = 810 Ohms. This is not a standard resistor size, however we had an 820 Ohm resistor which should result in an output voltage of 5.05 Volts.
iPod Solar Charger Prototyping
Wiring up the above circuit on a
prototyping breadboard with a 270 Ohm
R1 resistor, and 820 Ohm
R2 resistor we can confirm that the output voltage is 5.06 Volts - perfect for our
iPod charger. It is
essential to check that the output voltage is around 5 Volts using a suitable
multimeter before attempting to charge your iPod or the battery and/or iPod itself could be damaged.
Connecting the Charger to the iPod
The
iPod is supplied with a
USB cable. One end is plugged into the iPod and the other end has a
male USB-A plug. To connect this to the
solar charger a
female USB-A connector (socket) is required such as the one pictured below:
It can often be cheaper to buy a cable with a fitted female USB-A connector and cut it off to use in this project. Simply connect the red USB cable wire to the 5V positive output from the LM317T, and the black USB cable wire to the ground (negative).
According the chart below the 5 Volt output from the LM317T should be connected to pin 1, and the ground (negative) connected to pin 4.
...however when we made those connections using a scavenged male USB connector plugged into a similarly scavenged female USB connector the voltage output was zero. After a bit of fiddling around we found that connecting the ground to
pin 3 (rather than to pin 4) resulting in the expected voltage getting through as shown below.
Unplugging the test male USB connector and plugging in the male USB connector from the iPod, the charging icon appeared on the display indicating that our charger worked.
Now all that remains is to solder (or otherwise join) the connections to make them permanent. The whole small assembly can simply be superglued to the back of the solar panel, and the iPod cable plugged into the female connector as and when necessary.
Solar iPod Charger Schematic
Warning
Disclaimer - This is just a demonstration of how we built our solar powered iPod charger. We are not responsible if in following in our footsteps you damage your iPod.
Commercial Solar iPod Chargers
There are now a few high-quality commercially available
solar chargers supplied with adapters to enable direct charging of many mobile phones, hand held devices, and the full range of iPod models (except iPod nano). These include
Solio Solar Charger,
PowerMonkey-Explorer (pictured above), and
Freeloader Solar Charger.
These commercial chargers feature a small solar panel and an onboard rechargeable battery which in turn is used to recharge your iPod or other device. Prices start from around £25 for the
Freeloader up to £50+ for the
Solio and
PowerMonkey.
Article Last Modified: 10:00, 20th Jul 2007Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Solar Battery Charger With LM317TFind out how to make a current controlled solar battery charger using an LM317T
Article Last Modified: 08:34, 30th Mar 2007solar | education | electric circuitBasic 4 AA Solar Battery Charger PlansMake a simple solar charger for 4 AA rechargeable batteries
Article Last Modified: 08:43, 30th Jul 2007solar | educationLM317T Voltage Regulator ChipLearn about the LM317T and its uses in renewable energy projects
Article Last Modified: 13:35, 9th Sep 2008electronics | electric circuitUsing The LM317T With LED LightingUse an LM317T to regulate the current in LED lighting projects
Article Last Modified: 12:47, 12th Mar 2008lighting | electric circuitSolar Battery ChargingMake a solar charger for NiCd and NiMH rechargeable AA, AAA etc batteries
Article Last Modified: 08:43, 30th Jul 2007solar | educationPut Together an REUK Solar Lighting KitFull construction plans for solar powered shed or garage lighting using LED spotlights
Article Last Modified: 13:36, 25th Apr 2007solar | lighting | electric circuitMake a Simple Battery Status MonitorMonitor battery status with this easy electric circuit project - no skill required!
Article Last Modified: 12:33, 16th Mar 2007storage | electric circuitSolar Water Heating Pump ControllerBuild an electronic pump controller for a solar water heating system
Article Last Modified: 10:33, 9th Jul 2007water | solar | electronicsUsing The LM317T To Regulate VoltageUse an LM317T to regulate voltage in renewable energy projects
Article Last Modified: 15:04, 7th Mar 2008electric circuit | electronicsSteca PR 0505 Solar Charge Controller ReviewA review of the Steca PR 0505 Solar Charge Controller
Article Last Modified: 09:58, 23rd May 2007solar | shopping
|
|
|
